CD4066 DATASHEET PDF
The CDBM CDBC is a quad bilateral switch in- tended for the transmission or multiplexing of analog or digi- tal signals It is pin-for-pin compatible with. Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise . CD Datasheet, CD Quad Bilateral Switch Datasheet, buy CD
|Published (Last):||19 June 2009|
|PDF File Size:||1.73 Mb|
|ePub File Size:||17.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
This enables the signal at the input to go to the output. The switches are labeled from 1 to 4. In order for signals to pass through from the input side to the output side, the control or enable terminal must be HIGH.
HTTP This page has been moved
When pressed down, the pushbutton makes the signal HIGH. Applying these principles, you can easily see how to use all 4 switches if wanted. How to Build a Quad Bilateral Switch Circuit In this circuit, we will show how to connect a bilateral switch chip to inputs and outputs using the quad bilateral switch chip. Each switch has adtasheet single input and a single output terminal. This means that either side of the switch can be used as the input.
How to Build a 4066 Quad Bilateral Switch Circuit
When unpressed, the pushbutton has the signal LOW by default. In this circuit, we will show how to connect a bilateral switch chip to inputs and outputs using the quad bilateral switch chip. For this circuit, we are only going to be using 2 of the 4 switches.
In daatasheet circuit, we will show the basic functionality of the chip by passing analog signals through 2 of the switches by digital control.
So by a HIGH digital signal fed into the control terminal, we can pass an analog signal from the input terminal to the output terminal of the switch. V DD and ground, pins 14 and 7, are the power pins. The is a pin chip. The quad bilateral switch chip is a chip that is made up of 4 switches. The has a wide operating voltage of 5VV. Each switch has an input, output, and control terminal.
If the pushbuttons are not pressed down, then no signal will appear at the outputs. First, to power thewe connect 5V of power to V DDpin 14, and we connect the ground pin, pin 7, to ground.
How to Build a Quad Bilateral Switch Circuit
It can be obtained cheaply at a number of online electronic retailers. Each switch also has a control or enable terminal.
You can view the control terminal as the signal which closes the switch so that the input signal can cross over to the output. How the Circuit Works So, in order for datashee circuit to work, the pushbutton must be pressed down for each of the switches.
The pinout of the chip is shown below. With the control switch HIGH, then the switch closes and there can be an output.
The is a quad bilateral switch circuit, meaning that is composed of 4 switches. If a signal is fed into the input while the pushbutton is unpressed, no signal will appear at the output.
The most common waveform is a sine wave. This establishes sufficient power to the chip. A bilateral switch is so called because the switch can operate forward or reverse.
The control terminal enables the input to go to output. So you will see that if you press down the pushbutton with an analog signal or digital signal at the input, that same signal will appear at hte output. What this means is we feed an analog signal into the input of the switch and it reaches the output only if a HIGH digital signal is fed into the control or enable terminal. As the quad term implies, the is composed up of 4 switches.
So current can flow in one direction and the other direction, depending on which side is the input. The datasheet for the can be found at the following link: Without the control or enable switch, there can be no output. To the control terminals of the 2 switches, we connect a pull-down resistor pushbutton circuit. The is an IC composed of switches which are designed to switch analog signals via digital control. The really functions as an analog switch.
One place it can be obtained is at Taydaelectronics at the following link: To the inputs of the 2 switches, we feed an analog signal. A bilateral switch acts as a single pole, single throw switch.